Nistune Forums

Hey everyone.... So I finally go around to messing with my Altima again and Nistune will NOT let me edit the fuel maps. I'm stuck with all Closed Loop #s (128 value and up) and I and only edit the Values by doing up (which reduced the AFRs) This is a new issue that I've not come up against in the pa...

UPDATE!!!!! I found a really really old driver on the Moates Website for theFTDI chips and now Consult/everything is working perfectly! Matt, I know you stated that my Altima ECU part number is one that isn't really supported by the softwware. Now that I have full connectivity is there anything I ca...

Gotta question for you Matt..... I can run launch control with both my Calumsult RTv2 boards as long as I have an XDF that has launch control as a flag. Is it possible to use Nistune's LC with my Calumsult RTv2 boards??

Matt...... Do you have the VQ tables set up for the Ford 5.4L MAF (non-lightning)?

NVM..... I do have continuity on all wires from DLC to ECU as well as Power to the 12v ignition wire of the DLC. At this point I'm at a loss and I think it's got to be a driver/laptop issue on this car. OR I need to flash the daughterboard chipset, but I have no way of doing that since Calum has fal...

SO..................... I've just been driving the Altima as is. But now that the weather is warming up here in FL she's being a PITA to start on a "warm start". If the car sits for 45mins to 2hrs after I was driving it fights me to start. Cold start is no issue (fully cooled down). I deci...

That is my thought as well. I have attempted to contact Calum but we will see if he replies. It's been 4 yrs since we last spoke and I know he has moved to Illinois if I recall. So we will see. In the worse case I'll just order a consult cable and stream thru the factory DLC. I am gonna try one thin...

I assume you mean here that the emualtor part of Nistune cannot connect? This is correct. The emultor part nor consult is connecting Okay so you have ticked the emulator as 'calumsult' under File > Configuration? Nistune cannot connect to emulator, but Emutility can? YES Nistune uses its own versio...

Made a new USB cable for the Calumsult Daughterboard and still cannot connect. I tried a second laptop that I installed the drivers fresh with no other software other than ECUTalk and same issue! oh where oh where is the mysterious Calum when he's needed?!?!

NVM..... I tried to connect the laptop this morning and it wont connect AGAIN!!!! GRRRRRR!!! I'm going to replace the USB cable Calum originally supplied with the unit and cross my fingers. HOPEFULLY that will fix the problem

Hey Matt.... I uninstalled everything for a 4th time.... BUT this time someone turned me on to a program called FTClean. I reinstalled all the software, then ran FTClean which completely wipes out ANY FTDI drivers located in the computer. I then connected the ECU and it recognized that I was needing...

I have a U13 XDF that has Tables set up for Gasoline AND E85 if you'd like to have it.

With the ADR file I stated I was using I am able to modify the BIN I have from the original to the setup I now have. Your software is working good as far as being able to adjust the tables and BIN... but I just can't talk to the ECU with the software and have to use EmUtility to upload the BIN to th...

Thanks for the quick response Matt. When I connect the USB cable from the ECU to my laptop Nistune will not recognize my ECU at all. Correction to that statement.... ONE TIME it connected and had the "name" of the board where it would normally state "NOT CONNECTED" on the Nistune...

So I have had Nistune software for the past 2 months and it's working great with 2 of my 3 Nissans. It's working great with my S14 SR20DET as well as my S14 KA24DET. All 3 cars have Calumsult boards in them and the Altima and S14 SR20DET are the RTv2 boards..... Nistune loads and picks the correct A...