EGT sensr what to use?

[Bgtym]

how to write egt log?
thermocouple type K has a range of 0-54 millivolt = 0-1370 degrees Celsius.
If you connect directly DLP \ BP?
or without the signal amplifier will not work? wrong

http://temperatures.ru/pdf/Type%28K%29.pdf

[skylinegtrhr]

check this topic:

viewtopic.php?f=12&t=1279&hilit=Dlp+logging

[Bgtym]

check this topic:

viewtopic.php?f=12&t=1279&hilit=Dlp+logging

non-working link EGT))
I found another amplifier.
http://www.ebay.com/itm/Temperature-Sig ... 1393972432

[skylinegtrhr]

just look for AD595 chip but it is hard to find complete modul with it , I also did look at this you find but didn't try it please post yours experience when you try it.

and BTW if you also looking for IAT logging this is great and cheap sensor
http://www.banggood.com/Wholesale-DS18B ... 53674.html

[Bgtym]

I looked AD595, this chip amplification factor is high,
enhances 247 times that the output gives 0-15volt. 0-1270 degrees Celsius.
I will accomplish your goal on the results!

air temperature sensor I use 39340 37100 from Hyundai, this sensor Bosch!



pullup resistor 1K ohm

formula for calculating
Vect = 5000 * Rect / (Rect + 2680) ; where 2680 ohm is OEM ECU resistance between ECT input and +5V.

[skylinegtrhr]

this Facet EPS 1.994.019 is looking very simple to mount on pipes, nice find are you already using it for longer period?
I find it for 13€ do you have any source with good price?

[Bgtym]

this Facet EPS 1.994.019 is looking very simple to mount on pipes, nice find are you already using it for longer period?
I find it for 13€ do you have any source with good price?

in Russia it costs 3.5 dollars))

http://www.ebay.com/itm/SONATA-99-05-TR ... ab&vxp=mtr

[skylinegtrhr]

If Facet is good I'll rather use it as it have metal thread

btw you can look at schematic on page 142

http://www.innovatemotorsports.com/supp ... Manual.pdf

[Bgtym]

If Facet is good I'll rather use it as it have metal thread

btw you can look at schematic on page 142

http://www.innovatemotorsports.com/supp ... Manual.pdf

excellent manual, the diagram is worth a voltage divider chip after AD595
I thought to do the same,
but I find it easier to buy a ready-made board

[skylinegtrhr]

Hi few more questions
So I presume this is discussion about sensors?

http://turbobazar.ru/showpost.php?s=db6 ... tcount=413

so we can use this lookout table for all Bosch NTC N12 sensors? Fluid and air ?



http://www.bosch-motorsport.de/en/de/pr ... 199317.php

what is source of this table?

[Bgtym]

Bosch 0 280 130 039 analog 39340 37100 Hyundai.
table above that specifically for the Bosch 039
Accordingly, this table is applicable for the sensor 39340 37100 Hyundai
This table is used to control units Bosch!

[skylinegtrhr]

thx I already order sensor so I'll try this ... I also order very similar sensor for oil temp

[Bgtym]

thx I already order sensor so I'll try this ... I also order very similar sensor for oil temp

what temperature sensor you ordered for oil?
The sensor must be small in size,
which can be screwed into spacer plate oil filters

[skylinegtrhr]

febi 28381

no never put sensor on spacer it can brake,
Pete had seen some catastrophic results of that,
I always make teflon pipe and mount for this, and for SR you can buy block adapter and completely remove oem filter case and use only remote oil filter
http://www.frsport.com/Tomei-193068-N2- ... _2572.html

[Bgtym]

thermocouple amplifier


Sensor boost MPX4250
EGT K-type thermocouple
air temperature 39340 37100
the fuel/oil pressure sensor from the device DEPO or any other.