New User - few (tons) of Questions on CA18DET EDM ECU

[Matt]

Okay this looks good. We have LTFT and you can see the adjustments (in those cells traced) in the RAM tracer at 1500

[Matt]

Yes the knock count works on the version on the website, but I've disabled in the software unless the 'knock sensor' DTC box is ticked

2020-08-15 09_56_17-Nistune [S13 CA18DET FP1] Knock count.png

(17.82 KiB) Downloaded 1757 times

CA18DET didn't have the DTC addresses defined, so you can see them in the attached updated address file (put in Documents/Nistune/Address). I will include the updated version in next release

2020-08-15 09_57_42-Nistune [S13 CA18DET FP1_ DTC flags.png

(11.39 KiB) Downloaded 1757 times

[Matt]

Attached is the ENT file I used today for 39F0x ECU part number (with LTFT)

[PL]

Nice to have some stuff like this for the mighty CA. Shame we don't see more of them around here in SA.

PL

[Run_Stop_Restore]

Awesome Matt,

thanks a lot for putting so much work into this!

When i try to load the adr file you just posted it gives me an error. Let us know when the official re-release of the CA18DET V1.1 is done

[Matt]

What is the error message? It should work with the latest 1.3.29 released 4 days ago

[Run_Stop_Restore]

Hi Matt,

it shows:

Errors in Adress File cannot process!
Error: ROM OFFSET is not specified
Error: ROM ORIGIN is not specified
Error: ROM LENGTH is not specified
Error: CPU type is not specified.

All in one Error box.

Also: How can i open the Consult Ram Tracer with a Type1 Board that has no consult? I cant find the option anywhere.
BEst Regards
Felix

[Matt]

Hi Felix

Are you opening the file directly, or just putting it over the top of the previous one in your Documents/Nistune/Address folder?

You should just replace the previous version

RAM tracer is only available in Expert mode sorry. File > Config > Misc > User level = expert then restart, and you should see RAM tracer in Display > consult RAM tracer

[Run_Stop_Restore]

Hi Matt,
thanks for the reply.

Hi Felix

Are you opening the file directly, or just putting it over the top of the previous one in your Documents/Nistune/Address folder?

You should just replace the previous version

Tried both, if i replace it and go to Select Vehicle -> S13/RS13U12 Silvia/180SX CA19DET it seems to select another adr file.
Nistune asks me if i want to load the Feature Pack adr since it recognizes a feature pack 1 ECU but i tried both loading the adr file for FP1 and leave the File loaded that has been chosen automatically. Both without success so far.

I'll check with RAM Tracer.

RAM tracer is only available in Expert mode sorry. File > Config > Misc > User level = expert then restart, and you should see RAM tracer in Display > consult RAM tracer

Thanks, found it now.

Best Regards
Felix

[Matt]

Okay just wait for the next 1.3.30 release. I'll try and get that up Friday since I should have some time then

[Run_Stop_Restore]

Hi Matt,

i'll wait, your Friday is my Thursday anyway

[Matt]

Ran out of time Friday. Been crazy busy as usual. Anyway I've put the LTFT into 1.3.30 for S13 CA18DET (standard) + FP1 versions. Release going up now

2020-08-30 19_18_23-Nistune [S13 CA18DET FP1_ Flex Fuel + Launch Control (Version_ 5)].png

(53.47 KiB) Downloaded 1636 times

[Run_Stop_Restore]

Hi Matt,

no worries i was super busy as well and didnt even had the time to check until now.
Works perfectly fine.

Thanks
Felix

[Run_Stop_Restore]

Yeah just hold off for that then. I don't have an ETA unfortunately as I'm finishing up FP1.1/FP2.1 for SR20DET currently (half way updating my patching scripts), and then will go back to the knock count work after that

Hi Matt,

any update on FP1.1 re-release with cylinder selective knock count for Type 1 CA18?

Best Regards
Felix

[Matt]

No update yet on this one. I'm part time with Nistune, so adding extra features on top of normal support is only when I have free time