With the feature pack updates do I get fan control? I have spare output for the fuel enrichment sol and egr solenoid that are currently not used. I know the fuel temp is used for the launch. Just trying to confirm. would love to use these wires for something.
with the following what would be the best feature pack rom file to start with. currently on M30_VG30_F661F_K255AFA6_FAN_FP_TB45_maps.bin with current consevative tune.
Vg33et M30 Hxd35 on Water, 750 bosch, slot style 350z in factory, aeromotive stealth, 5speed.
thanks steve
M30 Ecu features
Moderator: Matt
Re: M30 Ecu features
Normally M30 VG30E ECUs do not have fan control. At one stage I was using these for TB45 engines
I would re-use existing outputs and convert them to fan control. So if you have the standard M30 ECU program loaded, these will not function
We also had to cut the ECU tracks from the reused outputs and route them to the fan control
So basically you need:
1. Reflash M30 ECU code to the TB45 / M30 code (ENT file - using base image programmer board. BIN file is only the maps)
2. Wire in Fan lo and Fan hi from the reused outputs (I've got a doc detailing the whole procedure but can put the write up here for the fans if you want it)
I would re-use existing outputs and convert them to fan control. So if you have the standard M30 ECU program loaded, these will not function
We also had to cut the ECU tracks from the reused outputs and route them to the fan control
So basically you need:
1. Reflash M30 ECU code to the TB45 / M30 code (ENT file - using base image programmer board. BIN file is only the maps)
2. Wire in Fan lo and Fan hi from the reused outputs (I've got a doc detailing the whole procedure but can put the write up here for the fans if you want it)
Re: M30 Ecu features
Attached are the instructions. Pages 5-6 are the wiring changes for Fan1, Fan2
The firmware flash file is : M30_VG30_F661F_K255AFA6_FAN_FP.ent
That needs to be reprogrammed in your Type 2 board using a Base Image Programmer. We sell these on the website, but many distributors listed on the website have these also (CZP, Houston Z, AVP, Ronin if you are in the states)
Once flashed in, you can adjust the fan control flags table values and Fan Control parameters
The firmware flash file is : M30_VG30_F661F_K255AFA6_FAN_FP.ent
That needs to be reprogrammed in your Type 2 board using a Base Image Programmer. We sell these on the website, but many distributors listed on the website have these also (CZP, Houston Z, AVP, Ronin if you are in the states)
Once flashed in, you can adjust the fan control flags table values and Fan Control parameters
- Attachments
-
- WiringM30_ECU_for_TB45E.pdf
- (1.11 MiB) Downloaded 145 times
Re: M30 Ecu features
List of M30 VG30E ECUs
F31 VG30E Infiniti M30 90 USDM F6610 N A F A18-A08 K30
F31 VG30E Infiniti M30 90 USDM F6615 N A C A18-A09 K31
F31 VG30E Infiniti M30 91 USDM F6660 N A F A18-A60 K32
F31 VG30E Infiniti M30 91 USDM F6665 N A C A18-A61 K33
F31 VG30E Infiniti M30 91 USDM F6670 N A F A18-A60 K34
F31 VG30E Infiniti M30 91 USDM F6675 N A C A18-A61 K35
These can be reprogrammed with F661F (Fan) to run TB45 (per the attached document)
F31 VG30E Infiniti M30 90 USDM F6610 N A F A18-A08 K30
F31 VG30E Infiniti M30 90 USDM F6615 N A C A18-A09 K31
F31 VG30E Infiniti M30 91 USDM F6660 N A F A18-A60 K32
F31 VG30E Infiniti M30 91 USDM F6665 N A C A18-A61 K33
F31 VG30E Infiniti M30 91 USDM F6670 N A F A18-A60 K34
F31 VG30E Infiniti M30 91 USDM F6675 N A C A18-A61 K35
These can be reprogrammed with F661F (Fan) to run TB45 (per the attached document)