0.9.2.66 version available

Matt · Post by **Matt** » Wed Aug 20, 2008 1:56 am

All details are on the downloads page. Some recently requested features have been added

Please note that I will be interstate next week, so I might not be on here much during that time. Taking the laptop with me so I can get some more features added

thanks
Matt

modulation · Post by **modulation** » Wed Aug 20, 2008 10:58 am

OMG this TPS Decel Cut option is the cats meow!
Thanks for including it so quickly Matt.

You guys rock!

lyckaon · Post by **lyckaon** » Wed Aug 20, 2008 4:41 pm

Hi!

You have add two news maps (Add map 1 and 2) what are their functions?

Thanks

Matt · Post by **Matt** » Wed Aug 20, 2008 6:23 pm

You mean parameters ADD_MAP1 .. ADD_MAP9?

These are use for defining generic tables which havent been specifically added to the software. Before they were ignored, but now they display as the required size table as specified in the address file

Unless you are talking about something else?

lyckaon · Post by **lyckaon** » Wed Aug 20, 2008 8:18 pm

Here are the two parameters:

TSL · Post by **TSL** » Wed Aug 20, 2008 11:50 pm

They are the old variable inlet manifold tables left over from the original ROM Editor address file for the jdm ca18det. They have always been there but nistune previously did not display them

It is incorrectly represented as it is actually a single 1x32 table not two seperate 1x16 tables.

I'm sure future updates will correct this.

Matt · Post by **Matt** » Thu Aug 21, 2008 12:10 am

Thanks. Looks like I've got some more address file updates to go! I'll have a look at the scalings that you've send through also

lyckaon · Post by **lyckaon** » Thu Aug 21, 2008 12:29 am

Thanks

TSL · Post by **TSL** » Thu Aug 21, 2008 2:07 am

Should be 1x32 table.
RPM lookup 1 = 25rpm. So.....

0rpm, 200rpm, 400, 600, 800,... ..., 5800rpm, 6000, 6200.

UNISA JECS · Post by **UNISA JECS** » Mon Aug 25, 2008 8:57 am

Hey Matt, I like the new features.

Have a question, I've noticed that my S13 KA24DE address file doesn't have the following and or it does but there appear to be some discrepencys or things left out:

Thanks

#Latency Change
VOLT_LATENCY_CHANGE,&H001A,1,1,1,1,Latency change with Voltage (DTS)

THROTTLE_ENRICH_COLD,&H0C20,16,1,16,1,Throttle enrichment cold start

THROTTLE_ENRICH_FAST_MOVE,&H0FC0,16,1,16,1,Throttle enrichment fast movement

COLD_START_NEUTRAL_MAIN,&H0C20,16,1,16,1,Cold start neutral main

COLD_START_NEUTRAL_SECONDARY,&H0c30,16,1,16,1,Cold start neutral secondary

IDLE_TIMING,&H0460,16,1,16,1,Idle timing (in gear)

IDLE_TIMING_NEUTRAL,&H0470,16,1,16,1,Idle timing (neutral)

IDLE_SPEED,&H0660,16,1,16,1,Idle Speed Control RPM

Now I dont know if they haven;t just need added yet or they aren't there for a reason. But if I open the S13_SR20DET_256_E.adr and open up a S13 KA24DE.bin and S13 SR20DET.bin and do a compare it shows everything, and everything looks similar but ofcourse different.

Could I add these manually?

Here a pic that will better show what differences I seen.

**Disreguard the VOLT LATENCY CHANGE on the S13 KA24DE adr (I added that as a test to see if it would show up in the .bin) BUT IT TO IS ALSO MISSING.

Matt · Post by **Matt** » Tue Aug 26, 2008 10:13 pm

I've actually been going through these address files updating them for the next ROM image pack. Attached is an updated version which I did last week, trying to add more addresses as I go. Let me know how you go with this for now. Sorry not much time whilst interstate to have a look but I'll update as required