Discuss software bugs and related problems here.
Moderator: Matt
-
Mads B (dk)
-
- Posts: 74
- Joined: Sat Mar 22, 2008 7:39 am
- Location: Denmark
Post
by Mads B (dk) »
i cant change the loadcells in ignition maps, works fine in fuelmaps
-
Attachments
-
- loadscale.JPG
- (169.44 KiB) Downloaded 3072 times
-
PL
-
- Posts: 957
- Joined: Fri Feb 03, 2006 3:29 pm
- Location: Adelaide, South Oz
-
Contact:
Post
by PL »
Have you tried changing the load scale values by selecting the load scales in the left menu rather than editing directly in the IGN maps?
PL
-
Mads B (dk)
-
- Posts: 74
- Joined: Sat Mar 22, 2008 7:39 am
- Location: Denmark
Post
by Mads B (dk) »
yes i have tried that but every time i push the buttom the value jumps 17 points up..... and its always up even when i push -/pagedown
1991 Nissan S13 CA18DET EURO Spec.
-
Matt
- Site Admin
-
- Posts: 8984
- Joined: Sun Jan 29, 2006 1:45 am
- Location: Adelaide, Australia
-
Contact:
Post
by Matt »
okay click on the cells below the scale, and then use the up key to move into the scaling bar area
this will then let you change the scaling using +/- keys
-
PL
-
- Posts: 957
- Joined: Fri Feb 03, 2006 3:29 pm
- Location: Adelaide, South Oz
-
Contact:
Post
by PL »
I tested this on the weekend by programming a 39F00 base image into a type 1 board and running it on the bench.
I was able to change load scale values by selecting the required cell (it goes dark blue) in the load scale editing box and using +/- keys to adjust.
No problems this end.
PL
-
Mads B (dk)
-
- Posts: 74
- Joined: Sat Mar 22, 2008 7:39 am
- Location: Denmark
Post
by Mads B (dk) »
it works
, but in fuel maps i just dual click on the value and i can write any number value
today in found out that i have same problem in every scale
jumpes 17 up regardles if push -/+/pageup/pagedown
i triede to edit in a s13 sr20det map with the right adr. file of coause no problems at all
1991 Nissan S13 CA18DET EURO Spec.
-
Mads B (dk)
-
- Posts: 74
- Joined: Sat Mar 22, 2008 7:39 am
- Location: Denmark
Post
by Mads B (dk) »
i can change rpm scale's same way i change load scale's from ign or fuel map.
1991 Nissan S13 CA18DET EURO Spec.
-
Mads B (dk)
-
- Posts: 74
- Joined: Sat Mar 22, 2008 7:39 am
- Location: Denmark
Post
by Mads B (dk) »
No one else with this problem ?
1991 Nissan S13 CA18DET EURO Spec.
-
Mads B (dk)
-
- Posts: 74
- Joined: Sat Mar 22, 2008 7:39 am
- Location: Denmark
Post
by Mads B (dk) »
hmmm... it works on my brothers computer... so it must be a problem relatet to my computer
1991 Nissan S13 CA18DET EURO Spec.
-
Matt
- Site Admin
-
- Posts: 8984
- Joined: Sun Jan 29, 2006 1:45 am
- Location: Adelaide, Australia
-
Contact:
Post
by Matt »
never seen that problem. so if you move the cursor into the scalers using the keyboard it still doesnt adjust?
what is the DPI on that computer under Display properites?