USB Device not recognized

Nistune topics specific to the 6802 cpu

Moderator: Matt

Post Reply
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

USB Device not recognized

Post by Crazy »

When i plug in my USB port for the first time i keep getting a;

"USB Device not recognized
One of the usb devices attached to this computer has malfunctioned and windows does not recognise it. "

Any one know whats wrong?
kenbam
 

Posts: 131
Joined: Sat Sep 15, 2007 9:46 am

Post by kenbam »

you have installed the correct drivers? What usb device is it?
Matt
Site Admin
 

Posts: 8990
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt »

sounds like you didnt get the drivers to install properly

Visit Device Manager and then find the Nistune USB device and reinstall the drivers for it. For more information please see the Type 1 USB installation manual on the documents page at www.nistune.com

This will detail how you install the drivers
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

Post by Crazy »

I can't get the drivers to install. windows XP
I worked 4 hours on it, still no install.
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

Post by Crazy »

The only change i made is going from a 85 turbo ECU to a 88 ECU with nistune. I did the dropping resistors and the injector rewire.
After i had the board installed i plugged in the ecu and started the car and it immediately flooded itself. :x

Is there a ROM image in the ECU, or do i need to load one?
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

Post by Crazy »

I cant get past "cannot continue the hardware update wizard"
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

Post by Crazy »

I just installed the current update and bought a new usb cable, no change :x
Attachments
nistune 002.jpg
(1.74 MiB) Downloaded 3357 times
Matt
Site Admin
 

Posts: 8990
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt »

can you screen shots of the error message of what you are seeing inside device manager? what is the status of the device?

You can use ALT-PRINTSCREEN to get a screengrab!

Then open up MS-Paint and use paste to see it. Then you can save that to JPG and post up on here

I dont know exactly what is going on with it at the moment??
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

Post by Crazy »

The replacement usb to board plug-in was one problem.
Crazy
 

Posts: 17
Joined: Fri Dec 12, 2008 2:28 pm
Location: Breckenridge Minnesota

Post by Crazy »

The replacement usb to board plug-in fixed the "unknowen USB device" problem and allowed me to install the drivers. :D
Matt
Site Admin
 

Posts: 8990
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt »

good stuff. so it was the connector cable to the USB socket?

can you please send the other bits back and I'll have to investigate what the cause of the problem is. Most likely a crimp connector not contacting the cable properly from the sounds of things
Post Reply