Innovate LogWorks 3 SDK Now available! (LM2)

Matt · Post by **Matt** » Thu Aug 13, 2009 11:13 pm

Innovate has release their SDK which is required for the LM-2 finally after over a year since promised!

I'll work on integrating that with the next beta release and I'll need people to let me know how it goes with their USB LM-2 devices. I only have the LC-1 here but should work the same in theory

skylinegtrhr · Post by **skylinegtrhr** » Fri Oct 09, 2009 2:37 am

Still can't connect with USB with LM2 even in newest version (0.9.13.8.b) I still have to use custom serial cable.

Matt · Post by **Matt** » Sat Oct 10, 2009 8:01 pm

so their device doesnt show up in the selection list?

I'm planning to get a LM-2 this week... my LC-1 stopped working

gets stuck in heater warmup mode and never finishes

skylinegtrhr · Post by **skylinegtrhr** » Sat Oct 10, 2009 11:51 pm

No it is showed as LM2 USB but when I hit connect it said can't connect. I try with and without installed Logworks3 with same result.
BTW it is working with Logworks3

Matt · Post by **Matt** » Sun Oct 11, 2009 4:43 pm

can you grab a nistune debug log file and post here?

Matt · Post by **Matt** » Thu Oct 15, 2009 4:24 pm

my LM-2 is in the mail and on its way over ... should be here next week and hopefully last longer than my LC-1 did

Matt · Post by **Matt** » Tue Oct 20, 2009 4:54 pm

okay got it. going to play with it tonight and get the thing working

Legionnaire · Post by **Legionnaire** » Tue Oct 20, 2009 7:05 pm

Out of curiosity - what happened to your LC-1?

Matt · Post by **Matt** » Tue Oct 20, 2009 10:59 pm

LC-1 after being left powered on the bench for a number of hours with sensor connected afterwards never could get sensor to heat up to 100% again and also increased power draw meant power supply couldnt cope

Sent Innovate an email about it tonight, both sensors work on the LM-2 but the LC-1 no luck. One thread on innovate forums about this issue but no real information. See what they reply back with. I would like to repair this one if its possible (only a number of chips inside)

LM-2 support works tonight anyway, tested on the bench

UNISA JECS · Post by **UNISA JECS** » Wed Oct 21, 2009 5:49 am

Matt wrote:LC-1 after being left powered on the bench for a number of hours with sensor connected afterwards never could get sensor to heat up to 100% again and also increased power draw meant power supply couldnt cope

Sent Innovate an email about it tonight, both sensors work on the LM-2 but the LC-1 no luck. One thread on innovate forums about this issue but no real information. See what they reply back with. I would like to repair this one if its possible (only a number of chips inside)

LM-2 support works tonight anyway, tested on the bench

My LM-2 cannot always heat itself to 100% also Matt, I haven't been tunning or messing with my car in a while but soon I will with my P11 turbo after I send you my ECU

.

So now the LM-2 well connect via the LM-2 provided USB cable?

skylinegtrhr · Post by **skylinegtrhr** » Thu Oct 22, 2009 8:07 am

Matt wrote:can you grab a nistune debug log file and post here?

here is debug log with 9.13.09 and 9.13.10 version but problem stay, I still can't connect and on logworks 3 lm-2 is working.

Matt · Post by **Matt** » Fri Nov 20, 2009 12:53 am

sorry with the delay. i've just started looking at this.

18:28:47.905 About to create MTS controls...
18:28:47.917 MTS Control OCX creation successful within this view

18:29:17.162 CMTSMain()
18:29:17.162 statusbar: Wideband 1: Connecting to Innovate MTS COM0

18:29:18.601 Wideband 1: OnSelMTSConnect: Detected ports 3
18:29:18.601 Wideband 1: OnSelMTSConnect: Attempting connection to 0 COM24
18:29:18.601 statusbar: Wideband 1: Connecting to Innovate MTS on port COM24

When you select a port, it gets saved as 'COM0' or a USB device

But later when I look through the list of COM ports it reads as COM24

If you have no com ports (like I do here) then it works okay.... I'll try a fix out for next release and test with LC-1 and LM-2

btw Innovate replaced my LC-1 no charge

Matt · Post by **Matt** » Thu Nov 26, 2009 12:22 am

okay now fixed. tested on machine with mulitple com ports

skylinegtrhr · Post by **skylinegtrhr** » Fri Dec 11, 2009 4:15 am

Problem still there , in attachment is debug log file , I select LM2USB but it throw me on other com ports . It's on windows XP and I can use serial converter without problem and USB with Logworks3

Amien · Post by **Amien** » Sun Jan 03, 2010 7:29 am

Gents any luck with this problem...