bypassing nats..

skylinegtrhr · Post by **skylinegtrhr** » Wed Oct 21, 2009 2:36 am

Hi Jez , can You please describe procedure (step by step) for synchronization of key's ?

baguete · Post by **baguete** » Mon Jan 04, 2010 2:39 am

I used H-DEV NATS recoder and it works fine on S14a and K11. The K11 gives an error at the end of the recode but Check Light went on and car started ok...

skylinegtrhr · Post by **skylinegtrhr** » Mon Jan 04, 2010 6:01 am

baguete wrote:I used H-DEV NATS recoder and it works fine on S14a and K11. The K11 gives an error at the end of the recode but Check Light went on and car started ok...

And what is procedure for synchronization? If You can please put "Step by step" procedure.

baguete · Post by **baguete** » Mon Jan 04, 2010 6:16 am

skylinegtrhr wrote:
baguete wrote:I used H-DEV NATS recoder and it works fine on S14a and K11. The K11 gives an error at the end of the recode but Check Light went on and car started ok...
And what is procedure for synchronization? If You can please put "Step by step" procedure.

Its easy, just connect Consult cable on both car and pc, run the H-DEV software program, choose the COM port, and click the "Sync!" button. Wait a few secs and its done...

skylinegtrhr · Post by **skylinegtrhr** » Mon Jan 04, 2010 6:39 am

Thanks I must try it with NIStune function.

baguete · Post by **baguete** » Mon Jan 04, 2010 7:00 am

skylinegtrhr wrote:Thanks I must try it with NIStune function.

Youre welcome.

I never used that NIStune function, but i will give it a try...

Fusion Ed · Post by **Fusion Ed** » Tue Feb 09, 2010 10:26 am

Key in ignition on
Sync (ECU light should stop flashing and stay steady)
IGNITION OFF
Second key in ignition on
Sync (ECU light should stop flashing and stay steady)
IGNITION OFF

Test both keys.

Do not try to start between adding keys.

baguete · Post by **baguete** » Mon Feb 22, 2010 1:31 am

Fusion Ed wrote:Key in ignition on
Sync (ECU light should stop flashing and stay steady)
IGNITION OFF
Second key in ignition on
Sync (ECU light should stop flashing and stay steady)
IGNITION OFF

Test both keys.

Do not try to start between adding keys.

Hi Ed, how many keys can NATS take? I was told 3, other say 4...

Fusion Ed · Post by **Fusion Ed** » Mon Feb 22, 2010 11:10 am

I have never tried more than two, so I cannot say for sure.

baguete · Post by **baguete** » Tue Feb 23, 2010 10:35 am

Fusion Ed wrote:I have never tried more than two, so I cannot say for sure.

Ok, thanks

skylinegtrhr · Post by **skylinegtrhr** » Thu Mar 25, 2010 10:45 pm

I try NATS synchronization with two S14a EDM without success with NIStune version 0.9.14.01 and 0.9.14.02

I put new ECU put contact , connect Consult and then press NATS synchronization and confirmed Yes on pop window,
it just said NATS response 0 in down left corner and nothing happen ECU lamp is continuing flashing I even try to let it for few minutes but nothing happen.
Which NIStune version is know good for this procedure?

baguete · Post by **baguete** » Sat Mar 27, 2010 3:45 pm

skylinegtrhr wrote:I try NATS synchronization with two S14a EDM without success with NIStune version 0.9.14.01 and 0.9.14.02

I put new ECU put contact , connect Consult and then press NATS synchronization and confirmed Yes on pop window,
it just said NATS response 0 in down left corner and nothing happen ECU lamp is continuing flashing I even try to let it for few minutes but nothing happen.
Which NIStune version is know good for this procedure?

Had the same problem, one S14a was synchronized fine, other wouldnt accept it, and the owner had to take it to a Nissan Dealer...

Any reason for this to happen?

Matt · Post by **Matt** » Sun Mar 28, 2010 11:43 am

I'll have to try it again then. Probably use Jez's NATS sync tool in the interium. I dont have a NATS vehicle to test it out on here

baguete · Post by **baguete** » Mon Mar 29, 2010 12:55 am

Matt wrote:I'll have to try it again then. Probably use Jez's NATS sync tool in the interium. I dont have a NATS vehicle to test it out on here

With H-Dev NATS Sync it happens again, no recode possible, only Nissan Dealer can recode it...

skylinegtrhr · Post by **skylinegtrhr** » Mon Mar 29, 2010 1:10 am

what is Yours ECU number baguete?
both car I can't do were 23710-82F09 but Pete put 82F08 image on them as there was problem with running original 23710-82F09 image ...

I also try on both car's one ECU without NIStune board but also without success .

Nistune Forums

bypassing nats..

Re: bypassing nats..

Re: bypassing nats..

Re: bypassing nats..

Re: bypassing nats..

Re: bypassing nats..