Nistune Forums

No that one isnt supported. only S13 KADE and S13 SR20DET i believe at the moment

No big deal for me really. Worse case get a msd setup and do it that way. Not to worried about it with my maxima. Would just be fun to play with.

Matt the last weekend I've use the new release and the Wideband Input Tracer not work are something wrong? beacause with the last version don´t have any problem.
I´m using AEM uego wideband and work fine with the program only don´t work the input tracer.
Look http://www.youtube.com/watch?v=jOZuVVykknc

Thanks.

okay thanks for letting me know - will have a look

robertsr20 wrote:Matt the last weekend I've use the new release and the Wideband Input Tracer not work are something wrong? beacause with the last version don´t have any problem.

I'm having the same issue on my S14 240sx KA24DE as well.

robertsr20 wrote:Matt the last weekend I've use the new release and the Wideband Input Tracer not work are something wrong? beacause with the last version don´t have any problem.
I´m using AEM uego wideband and work fine with the program only don´t work the input tracer.
Look http://www.youtube.com/watch?v=jOZuVVykknc

Thanks.

SAME,

No AEM wideband input working in the AFR Tracer
It logs the values, but the does not display any values in the spreadsheet.

S14 Silvia w/SR20det

Also, any word on a launch control/two step for this setup?

Thanks


PS: I've been around for a year and this is my first post??

use the previous version in the interim (0.9.14.2)

I'm aware there is an expiry of about 20 days remaining but I'll get a release with the fix up on Friday

Okay sunday... 0.9.14.10 now available

it was a silly bug with the AFR tracer so I've fixed that. Also doing some updates with S14 SR20 (will affect other SR20s) with temp enrichment

Added extra RPM limiters for Y33, ER34, WC34

BNR32 looking at Air intake tables. Two limit tables found so far and there are two others still looking at to see what they do

Still to look at the Z32 connectivity issue. Probably be another release this week as I start working through the list again

Sorry nothing yet on the base image programmers. Been looking at temp enrichment for various ECUs this week and reverse engineering takes some time

0.9.14.10.1b uploaded tonight

Address file updates I was doing for S14 SR20DET had affects on other ECUs in the enrichment tables. I have been looking at this

Anything which is
S13/S14/S14A/S15 SR20DET (JDM) will have 4 enrichment tables (TPS on/off and temp select)

Otherwise
N13/P10/B13/S13/B14/S14/P11 etc SR20DE/KA24DE will have 2 enrichment tables (temp select)

Noticed on S13 KA24DE that fuel cut/recover is missing now under enrichment tables

they werent the correct tables from what I could determine (looked like them but they didnt cut when they should have on the bench). I'm going to have to start again with trying to find those ones for SR20 again...

Sorry to bug you Matt again on S13 KA24DE,

TTPmin and TTPmax are different than last release.. unless it's just me!

edit - TTPmax still at 03A0, TTPmin used to be at H0390 and is now at 0A00. Is there a reason for this? Thanks.

TTPMin was wrong after further investigation and 0A00 responded on the bench and affected minimum pulsewidth. Also checked against the KA24DE/SR20DET code and this proved correct

Different to earlier ECUs which had the addresses next to each other in the map area

0.9.14.11b tonight up

- RB20DET, CA18DET etc are the same. I've fixed up the scaling display
- Fixed up crash issues (!) with Innovate wideband connect and then sync as well as some other thread related crash issues now fixed
- Added another MAF (J30 VG30DE late model)
- Found that 1988 Z31 doesnt have a neutral input switch (no change)
- Extra RPM limiters for ER34/WC34/Y33 added to address file
- Address file fixups for Z32 and R32 added
- Consult offset for TB42E added

Sorry cant find any problem with locating USB consult or third party USB converters. They show up inside Nistune on my machines fine. Also checked file configuration history and no changes since Mar 09 with detecting COM ports. Not sure what is going on there

0.9.14.12

Updated last night
- Innovate wideband updated to allow usage of Aux5,Aux6
- DLP Design A/D converter update for Aux5, Aux6 and precision fix
- Consult reconnection updates to persist and stay with current state with regards to communications problems during retrieving registers, register table, part number (currently displays 'no registers found')