Nistune 0.10 Release

[body80]

Running 10.06
Speed isn't correct for my ECU
US KA 240SX
I have it set to MPH. I know I was going faster then 29mph

t right.jpg

(390.7 KiB) Downloaded 3084 times

[Matt]

not sure on that one. I'll check it out on my next run just in case km/h is wrong

I just tried 174km/h which converted to 108mph once I adjusted it which is correct

[body80]

not sure on that one. I'll check it out on my next run just in case km/h is wrong

I just tried 174km/h which converted to 108mph once I adjusted it which is correct

I've got about 30 min of logs with 10.06 that say I never got faster then 30mph.
That's impossible where I live.

[Matt]

Ill check if its the recording doing something bad with imperial set

[louiswun]

Version 0.10.6 error report
Type 1 board on S13 CA18DET
TPS numbers inside wideband input tracer always show 72

[Matt]

TPS numbers inside wideband input tracer always show 72

This is the TPS output from your Zeitronix wideband unit. The Consult TPS is displayed as 'Throttle position' whilst TPS from Zeitronix does update if you have this connected (tested tonight)

[louiswun]

TPS numbers inside wideband input tracer always show 72

This is the TPS output from your Zeitronix wideband unit. The Consult TPS is displayed as 'Throttle position' whilst TPS from Zeitronix does update if you have this connected (tested tonight)

Oh...sorry !

[Matt]

I've got about 30 min of logs with 10.06 that say I never got faster then 30mph.

Okay I've located this issue. As I suspected recording mph when it should be kph and then convert it back to mph on playback. Also same problem with temperature and MAF translation for VLT/Z31. Testing further over this weekend with other changes before putting up a release

[TM_S13]

yesterday while doing some small adjustments and some logs I detected that the AFR graph on the log player is not showing...
the rest seems to show/work fine... the input tracer also works fine.
this is on type1 board, s13 ca18det.

[Matt]

AFR graph known issue. Fixed. 0.10.7 planned release sun

[bachig24u]

hi Matt,
I have a crash dump from debug mode and MS.

XP pro-SP3, 0.10.6, LC-1 via belkin usb-serial, consult connected.

flicking through timing table and bam, gone.
fault address 0x0012708c in MS-events logs.
also a minute after the nistune crash mptelemtry MPsigdwm.dll error instance occurs in MS-logs application also.

[bachig24u]

crash02.jpg

(56.43 KiB) Downloaded 2865 times

crash01.JPG

(38.61 KiB) Downloaded 2865 times

[Matt]

Thanks for the log files. Will have a look into it

[Matt]

Nistune 0.10.8 Release

Consult uploads bytes when constant window opened with 'auto' ticked
Comparison value for constants 8 bit incorrect
Fit to graph logging
LM-1 min/max display values
Com port default detection time increase to 7 seconds
Consult callback timeout causing issues. Crashes some machines
Installer not moving log files and BIN files
Z32 ECU highlighting knock map on high gear
Injection recovery table remaining highlighted at idle
Knock count beeping when going from lower to higher cell
Use Logworks MTS.DLL instead and remove Nistune DLL
Fix throttle open offset to RPM scaling
Limit injection latency to 2550uS
Fix AFR graph display
Log recorder recording imperial instead of metric values
Add consult logging for fuel and timing knock maps
Fix constant window comparison and low value 16 bit issues (affecting Z32 inj mult)
Fix zexel connectivity and gauge display issues
Add Consult 2 DTC codes
Remove log knock indication since counter rather than flag
Stop logger fast play from freezing
Update log path from previous saved value when hitting browse
Log player navigation improvements for zoom, fit and scroller
Clear out non displayable sensors in log player on disconnection
Log recording stop on new inputs found.
Don’t pause logger on unintentional device disconnect
Fix problems with knock map indication Z32, HCR32, S13 CA18
Fix 10 second callback timeout on consult disconnect issue on reconnect
Refresh gauges to disabled on consult disconnect
Add diagnostic code starts back into code
Fix reset on flags tickbox panel
Disable fuel map below 128 when VE map in ECU
Add maptrace for Add Fuel and Throttle Open Offset tables
Fix RPM scaling tracing for VE table
Fix RPM limit decoding for ER34, WC34, K11 etc with 16 bit RPM address
Fix RPM display for Zeitronix
Holding down +/- on table speed up functionality (10s then 100s)

Notes: Another interim build whilst working through outstanding issues. Known crash problem still with Innovate disconnecting at times. Random and difficult to diagnose but working on it

Important: Nistune no longer ships with LogWorks DLLs. You must have LogWorks3 installed. Nistune will deregister MTS.DLL it normally comes with and attempt to reregister MTSSDK.OCX in your C:\Program Files\LogWorks3\mtssdk.ocx area

If you dont have it installed here you will need to reregister it by opening a command window and going to the LogWorks folder and typing in:
regsvr32 mtssdk.ocx

Alternatively reinstall logworks3 which will re-register this file. Otherwise 'Innovate MTS' will not display inside Nistune

Tune files:
Nistune installer now moves any remaining log files to My Documents\user\Nistune\Logs and any BIN files in \Program Files\Nistune fold to My Documents\user\Nistune

Additional Consult 2 DTC codes including NATS malfucntion codes are now displayable. I'm working on adding Consult 2 registers but there are heaps of them... and the display and values of these depend which ECU you are using (for example injection time has 4 different interpretations!)

btw 0.10.7 was a test release but never put up on the website

[TM_S13]

going to try this new version soon.
also updated the logworks 3.02 to 3.07 ...

I hope nothing goes wrong since I'm yet to have some sort of comunications trouble. up until now it has been flawless.

I'll let you know.

type1 board ca18det s13