Page 1 of 1
how to connect LC1 to nistune?
Posted: Mon Aug 10, 2009 10:42 am
by Anders_r
Hello guys
I have tried the search but did not find, maybe i search bad ^^
anyway: how to connect LC1 to nistune?
maybe someone can link a picture how u did ?
/Anders
Posted: Mon Aug 10, 2009 6:06 pm
by Matt
connect 3.5mm connector with serial port to USB-serial converter and then to laptop
find the COM port with this converter inside Device Manager and then set this up in the configuration Wideband section (see wideband section in software users manual)
As for the rest of the wiring see the LC-1 manual which has the details for hooking it up
Posted: Mon Aug 10, 2009 10:26 pm
by Anders_r
Matt wrote:connect 3.5mm connector with serial port to USB-serial converter and then to laptop
find the COM port with this converter inside Device Manager and then set this up in the configuration Wideband section (see wideband section in software users manual)
As for the rest of the wiring see the LC-1 manual which has the details for hooking it up
The 3,5mm cable u can buy yes?:) or this will be homemade?
I only need 1 cable where my paint is and then usb to laptop yes ?:)
Posted: Tue Aug 11, 2009 9:53 am
by Matt
your LC-1 should have come with 3.5mm-serial plug. mine did
if not contact innovate to find out why its missing
Posted: Thu Aug 13, 2009 10:02 am
by Anders_r
looks like i got problems with my installation (it was there when i bought the car)
let me give u a pic!
:
These 2 are behind my AF gauge. the "in" is probably from the sensor ? cuz when i unplug it the gauge dont dont show afr anymore.
and then the "out" when i tried to find that cable .. i found that that was the cable to the pc??? so when i changed those 2 places i got it working in nistune but it shows 16,7 in idle on nistune and 14,7 on my gauge. but then i switch them back and now my gauge shows
new pic: whats whis ;/
i think its 14,9 my but the "1" is gone ;( why
Posted: Thu Aug 13, 2009 7:34 pm
by John
If Nistune and the wideband display shows different values you most likely chosen the wrong Wideband lookup table in the Nistune configuration.
Your gauge then is either broken or the cable in the back is not thoroughly connected.
Regards
John
Posted: Thu Aug 13, 2009 9:05 pm
by Anders_r
John wrote:If Nistune and the wideband display shows different values you most likely chosen the wrong Wideband lookup table in the Nistune configuration.
Your gauge then is either broken or the cable in the back is not thoroughly connected.
Regards
John
how can i get broken just if i change the cables? :S
the nr "1" is working cuz when i get power of and on its works and when car starting only 4,9 :S
Posted: Thu Aug 13, 2009 9:49 pm
by Anders_r
about the nistune, the lookup table is set at "innovate
Posted: Thu Aug 13, 2009 11:00 pm
by Anders_r
got it working now
Posted: Fri Aug 14, 2009 1:26 am
by John
Anders_r wrote:got it working now
What was the problem?
Posted: Fri Aug 14, 2009 1:46 am
by Anders_r
I really dont know
i just mixed some cables and sone violence
and now working good
LC-1 vid
Posted: Sun Jan 31, 2010 12:26 pm
by zmyzgo
Hope this comes through:
http://www.innovatemotorsports.com/vide ... ntent.html
getting ready to do my permenat hook-up.....
