Page 1 of 2
Nistune type 1 compatible with the engine CA18ET?
Posted: Sat Dec 05, 2009 6:41 am
by seb.racing
hello everyone,
I raise the subject, the engine CA18ET
engine nissan silvia S12 and bluebird U11T
turbo (T2) 8-valve and injection
documentation in the description
there was this
NIStune Type 1 Boards
CR31 Skyline (RB30E)
VL Commodore (RB30E)
VL Turbo Commodore (RB30ET)
Z31 300ZX (VG30E, VG30ET) 1984-1985, 1986, 1987-1989
A31 Cefiro (RB20DET)
J30 Maxima (VG30E)
S12 Gazelle (CA18)
S13 Silvia (CA18)
S13 Stanza (KA24E)
N12 Pulsar Exa (E15ET)
N13 Pulsar (CA18DE)
thank
PS: I'm new, there is a topic for presentation membres?
Posted: Sat Dec 05, 2009 7:39 pm
by Matt
yes can do CA18ET now
I have part number 23710-D4600 (MT)
What part number do you have?
Posted: Sat Dec 05, 2009 8:59 pm
by seb.racing
ok, it's cool
I'm going to see the numbers, and I am writing
From the description nistune type1? we obtain the function on the
Diagnostic Consult for CA18ET, if I understand correctly?
sorry for my English medium
Posted: Sun Dec 06, 2009 3:35 pm
by Matt
we report diagnostic codes and display them.
there are no 'active tests' on Type 1 boards though
Posted: Mon Dec 07, 2009 6:20 am
by seb.racing
ok, it's just info sensor and actuator
it is already good.
I have reference my S12 ECU is 23710-24F01
I wanted to open the lid of the ECU for a photo, but a screw is dead,
I'll look later
I have a Bluebird with CA18ET in my garage, I look to the tomorrow reference
thank
Posted: Mon Dec 07, 2009 8:45 am
by Matt
not sure on the S12 one. 21F13, 33F01 and 30F10 is what I have here
i would need you to remove the ROM chip, read out the image using an EPROM programmer and send the BIN file through
Posted: Wed Dec 09, 2009 4:50 am
by seb.racing
Matt wrote:not sure on the S12 one. 21F13, 33F01 and 30F10 is what I have here
the 23710-33F01 and 33F02 are version european no-catalyst
Matt wrote:
i would need you to remove the ROM chip, read out the image using an EPROM programmer and send the BIN file through
you talk using this equipment?
Matt wrote:yes can do CA18ET now
I have part number 23710-D4600 (MT)
What part number do you have?
I find the model number 23710-D4600 is for ECU Bluebird T12 & T72 version european no-catalyst
I'll disassemble the ECU of my bluebird U11 for verification
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Tue Oct 05, 2010 8:17 pm
by streetbike
Is there some news for the s12 CA18ET ?
type 1 board possible or not ?
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Sun Oct 10, 2010 12:36 am
by Matt
I dont have a rom image and nothing has been done with this one yet
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Mon Oct 11, 2010 8:19 am
by streetbike
I can upload the original .bin but nothing more ...
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Mon Oct 11, 2010 4:53 pm
by Matt
Email it through and I can have a look
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Sun Nov 21, 2010 10:40 pm
by seb.racing
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Sun Nov 21, 2010 10:59 pm
by Matt
looks same as a Z31 ECU. Just need the BIN file from the 28 pin chip on that ECU to check it here
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Fri Jul 15, 2011 7:38 am
by seb.racing
Matt wrote:looks same as a Z31 ECU. Just need the BIN file from the 28 pin chip on that ECU to check it here
sorry for my absence
you want the data from the chip?
I will gather additional pictures
Re: Nistune type 1 compatible with the engine CA18ET?
Posted: Fri Jul 15, 2011 11:27 pm
by Matt
Yes I need the chip removed from the ECU and read using an EPROM programmer so you can email me the BIN file
