Page 1 of 1
LC-1 not reading correctly in Nistune.
Posted: Mon Apr 28, 2008 5:26 pm
by 87calais
Hey.
Recently Purchsed an LC-1 so i can start tuning, but i cant get it to read correctly in Nistune. If i open the Logworks software it seems to read right, however in Nistune it just pretty much sits on 32afr. If you give the throttle a few stabs it flicks to 8afr for a second before returning to 32afr. I tried adjusting the lookup tables but it only made it read whatever the max value i put in there was. Anyone came across this before?
I have Nistune setup with wideband as innovate MTS and the lookup tables as Innovate. Have looked around in the configuration etc but cant seem to find any reason this might be happening.
In the lookup tables it shows 0v = 8afr and 5v = 32afr.
Any ideas welcome.
Cheers guys
Scott.
Posted: Wed Apr 30, 2008 10:53 am
by Matt
Hi Scott
Email me a debug log and your wideband config files and I can have a look through them
It should translate a raw value 0-1023 from the innovate to value between the ranges that you map to
Posted: Wed May 07, 2008 11:50 am
by vn_luke
Having the same issue - was any progress made with this?
Posted: Wed May 07, 2008 7:00 pm
by Matt
No log received yet. If you can post me yours then I can have a look at it
Posted: Thu Nov 27, 2008 10:08 am
by 87calais
Sorry about the rather late reply guys, haven't been able to spend much time on the car lately.
Originally i was having a heap of trouble getting the wideband to talk to Nistune, I got a new USB - serial converter and updated to the latest version of Nistune and for the most part it seems to work well now. I think the culprit was the converter.
The AFR in the wideband window now updates nice and quick as it should and reads correctly, my only issue now is in the log player, the reading for the wideband is approx double what it should be (double what it reads in the wideband window).
Any ideas on this one?
Scott.
Posted: Fri Nov 28, 2008 12:56 am
by Matt
noted and will have a look into it. like the scaling used is incorrect.
doesnt make sense at this time why its doing that. I've got an LC-1 so can try out here so will give it a go tomorrow and post on here. What Nistune version are you running right now?
Posted: Fri Nov 28, 2008 11:29 pm
by 87calais
Current version is 0.9.2.71
Also i noticed that when i view the consult gauge screen and show my wideband, the needle points to the correct number, but the digital readout shows the higher value. See pic below.
Quite possibly something I've done wrong, but i have checked everything i can think of and cant work it out.
Thanks,
Scott.
Posted: Sat Nov 29, 2008 10:58 pm
by Matt
its a problem with the translation to text within the guages. the needle is correct but the text string is wrong. will investigate this weekend
Posted: Sun Nov 30, 2008 9:11 pm
by 87calais
Thanks Matt.
Posted: Fri Feb 13, 2009 3:43 pm
by Matt
still got this one open. playing around with the LC-1 again on my car hopefully this weekend and will look into the fix
Posted: Mon Feb 16, 2009 12:27 am
by Matt
seems to be working now. next release...
Posted: Wed Mar 04, 2009 9:36 pm
by 87calais
Thanks Matt, looking forward to it!
Posted: Thu Mar 05, 2009 11:30 am
by Matt
On another note, my innovate unit keeps getting comms errors when i use it in the vehicle. Even with LogWorks. I'm going to have another look at that, but might be a wiring issue?
Just seems to freeze on a number (logworks reports comms sync error)
Posted: Mon Mar 09, 2009 11:42 pm
by 87calais
I haven't had any problems like that.
Sometimes Nistune will freeze, but im sure that's just my crappy old laptop. No errors, just freezes. This laptops about 10 years old, only gets used for the car. Might be time for a new one.
Tested the new version, all the numbers look good now on the gauges and log player. Top work Matt.