Nistune Forums

thanks for this info matt ! what i didn't understand at first is that from the DLP aux 1 input is not the same with nistune aux 1 ! i get the conclusion that DLP aux 1 is basicaly afr 1 in nistune , aux 2 DLP is afr 2 nistune , aux 3 DLP is aux 1 in nistune ... here is something that wasn't very cle...

thanks eric ! i was very tired last night... started fresh this mornig and did find the high gear fuel map , but only after i have reloaded the adr file. when burn it to the ecu worked fine, after read it from ecu seems to not load that fuel map...strange. does it need all the time to load the adr f...

didn't let me put more than 3 attch so here are the bin and the log. at the begging of the log are the gears changing 2nd , 3rd and 4th . on the 3rd about in the middle of it there is a low tps for a moment because the car started to go sideways and i had to let the gas a little . please look at the...

so far i have made this , see the pictures and seems to work much better now. still dies when coming from 4000rpms but up to that point of rpms comes down prety good and keeps the idle after a little bit of hunting. will do again a boost leak test to see if there is something else coming up and will...

eric, i know the q45 maf is going for 500 , but i still can alter the maf table so for a given voltage to "messure" less air , right ? and still play with the tp scalers so when i hit 1.6 bar ( i think that will be close to my target ) to be in the last two columns . this is my thinking .....

thanks for everybody's input here ! matt , i have tried both z32 maf table and q45 maf table and seems to work better with z32 , that's why that table in the bin. thanks for the new bin , will try it out today ! so from what i understand it is better to use that z32bin for rb25 than the z32 bin , ri...

thanks for that link ! exactly same problem here ... but i do have 90* elbow 4" diam and in total lenght about 20" so it should be enough air volume there ... i will try with a plastic pipe to see if changes something

yes , exactly ! do you have any ideea ? was thinking of that , but can't understand why...and is going very rich , i can see black smoke coming from the muffler also the AFR is out of scale ! want to mention that i have cleaned the AAV valve , HKS blow off is adjusted to max and also tried to block ...

long story short : 1. nissan skyline r33 , engine rb25det fully forged with Z32 ecu , 630cc injectors , q45 90mm maf , plus a lot of mods but don't meter here... 2. oem ecu (rb25det) #21U01 , Z32 ecu #31P02 3. i have ordered the type 2 board from RSP in UK . ( very bad experience , allmost 1 month o...

more testing ...more strange things ... i have disconnected all inputs and gnd from dlp , only afr wire input left on : 1. afr on nistune is 10 and stable no meter what afr is on the gauge 2. erased everything in the aux4 ,aux5 , aux6 files so should read 0 , but aux4 is named "T" in nistu...

here are the things... wideband PLX gauge with SM-AFR egt PLX gauge with SM-EGT map AEM 50psi map sensor dlp ch1 AFR analog from plx , ch2 map from mao sensor , ch3 egt analog from plx i used 5v out from dlp to power the map sensor all grounds together form dlp and gauges to the chassis nistune conf...

hello

any news regarding this ? i have also the same combo and in a few days i will received the nistune board from dealer and don't know how to work this AFR monitoring with nistune.

hey again :D it-s you again helping me :wink: i have found the wiring for this maf so for anyone interested with same set up for a ca18det without lambda : the maf has 4 wires like this green/black.......signal from maf (0-5v) black/white........12v from source (car) black.................ground(fro...

thanks alot...
i'm going with the steps that you have told...and see what you be...right now the ca18 is all the way 10.1 afr or rich ,out of plx scale
i hope that in a few days i'm going to receive the bord and the cable and then start working on the soft
thanks again

i have a z32 maf (n62) and want to put it on the ca18det. the problem is that i didn't find the wiring for a non lambda setup maf has 4 wires...
anyone have an ideea ?
thanks