Rev limiter?
Moderator: Matt
Rev limiter?
I'm not sure how off my tach is off but I tried to set the revlimter to 8500 but it zipped right past it to 9k. I tried to record the log but it seems to go crazy.
- Attachments
-
- wottest_2010-05-13_1604_18.csv
- 1st to 2nd then to 3rd where I slowed down.
- (54.4 KiB) Downloaded 367 times
Re: Rev limiter?
most tach's are a bit off ... and 500rpm off, at that RPM ain't uncommon.
how does the tach behaves in the rest of the RPM range ?
is it spot on ?
how does the tach behaves in the rest of the RPM range ?
is it spot on ?
Re: Rev limiter?
Yeah it's spot on. The VVL kicks at the right Rpms on the tach.
Re: Rev limiter?
Tested it on the dyno today. Limiter was set @ 8300 The pull stopped at 9k no revlimit past 8k 
.
.Re: Rev limiter?
does this mean the stock nissan ecm can't control anything past 8K>
Re: Rev limiter?
On the SR20's so far it looks like that. I haven't tried it with my RB20 since I don't need to rev past 8k.
Re: Rev limiter?
damn it i thought i'd be able to rock out nistune on my RWD VVL Swap i'm about to do. but i want to spin it to 8500 - 9K
Re: Rev limiter?
Not at this time, There is always tuner-pro but I don't know if they have it for the RWD sr20 ecu's. That will do over 8k.
Re: Rev limiter?
You need tunercode (modified Nissan code) to get above the 8000rpm mark
Re: Rev limiter?
Well that's disappointing news as i had always thought that nistune sorted that issue and was a point that i used make about it. Bummer.
Its a shame that making a board for the SRxxVE ecu (2N500/5J000) is so hard (and i now realise why after doing some reserach about it) because i know those ECUs support way high limiters (9.5K tried and tested).
Its a shame that making a board for the SRxxVE ecu (2N500/5J000) is so hard (and i now realise why after doing some reserach about it) because i know those ECUs support way high limiters (9.5K tried and tested).
Re: Rev limiter?
Nistune has never supported anything more than tuning the existing Nissan platform. There are no extras like launch control, flat shifting etc because it takes a long time to implement and its specific to each ECU
Consult patching is pretty generic once I separated the three firmware types and can run them over all the part numbers. Anything more specific is a custom job
Tunercode was aiming to fill the gap by making highly customised code but not sure where dave went with that one after calumsult shut down
Consult patching is pretty generic once I separated the three firmware types and can run them over all the part numbers. Anything more specific is a custom job
Tunercode was aiming to fill the gap by making highly customised code but not sure where dave went with that one after calumsult shut down
Re: Rev limiter?
so here is my question, even though it wont add a rev limiter past 8K RPM can we still tune that High and use an aftermarket rev limiter. say for example the Gizmo 2 step rev limiter? per say I only want to rev to 8500. can I adjust the table resolution accordingly. (further apart i guess that would mean) with the last cell being 8500 and the ecu will be able to keep up and make corrections / changes up that high?
Re: Rev limiter?
Even if the last cell is set to 8500 it will only read up to 8000. So the last cell value @ 8k is what it carries out to 8500 or 9000. It tends to get richer from what I have noticed.
Re: Rev limiter?
From my experience most Nissan ECU's will quite happily run right off the end of both RPM and load scales with no ill effects. Which I still find amazing. But that's what they do. 
PL
PL
Re: Rev limiter?
bumping this up to see if anything can be done? I hate reving without a rev limiter.