just got my engine startet, but seem to have some problems with the Pc>ECU connecting.
I have switched on ignition, pluged the cable to my labtop and when I press F8 in Nistune, I get this "Consult Not Connected"
When i Plug the cable or switch on ignition I hear the labtop give a sound, sound when a cable is pluged into USB
I have installed Nistune program and nothing else. I have a Log File
NISTUNE LOG Nov 14 2008 23:00 0.9.2.73
11:12:04.176 CNistuneDoc - usb disconnected
11:12:04.266 CImageSelPanelView
11:12:04.266 ConsultMain()
11:12:04.266 CConsultSM::CConsultSM
11:12:04.266 SetConsultMode(): From 14 to 0
11:12:04.266 CImageSelPanelView
11:12:04.266 CRomulatorSM::CRomulatorSM()
11:12:04.266 RomulatorMain()
11:12:04.266 ProcessRomualtorQueue(0) - Entering thread
11:12:04.266 CImageSelPanelView
11:12:04.266 CRomulatorSM::CRomulatorSM()
11:12:04.266 RomulatorMain()
11:12:04.266 TriggerRomulatorEventTask(1) - Entering thread
11:12:04.266 ProcessRomualtorQueue(0) - Entering thread
11:12:04.266 CImageSelPanelView
11:12:04.266 USBMain
11:12:04.266 InitialiseRegisters
11:12:04.266 CNIStuneDoc(): Zeroising target AFR table
11:12:04.266 CNIStuneDoc(): Initilising sensor record table
11:12:04.306 TriggerRomulatorEventTask(2) - Entering thread
11:12:04.326 CNIStuneDoc(): Initilising RPM AFR trace table
11:12:04.326 CNIStuneDoc(): Initilising consult
11:12:04.326 ConsultGetActiveSelections()
11:12:04.326 Unable to load afr1.csv lookup table - empty file
11:12:04.326 Unable to load afr2.csv lookup table - empty file
11:12:04.326 Unable to load aux1.csv lookup table - empty file
11:12:04.326 Unable to load aux2.csv lookup table - empty file
11:12:04.326 Unable to load aux3.csv lookup table - empty file
11:12:04.326 Unable to load aux4.csv lookup table - empty file
11:12:04.326 Unable to load aux5.csv lookup table - empty file
11:12:04.326 Unable to load aux6.csv lookup table - empty file
11:12:04.336 CImageSelPanelView
11:12:04.346 CImageSelPanelView::OnInitialUpdate
11:12:04.346 About to create MTS controls...
11:12:04.366 MTS1 Control OCX creation successful within this view
11:12:04.366 UpdateAllCombinationLists()
11:12:09.223 statusbar: Not connected to consult!11:12:09.223 OnConsultResync(): Not connected
11:12:12.978 OnCloseDocument:: Windows request doc close but windows still open
11:12:12.978 OnCloseDocument:: Windows request doc close but windows still open
11:12:13.038 ~CImageSelPanelView
11:12:13.038 ~CMapTraceDisplay
11:12:13.038 ~ThinChildFrame
Hopefully there a genius on the board that can guide me through this
But, on the bright side, the engine fired up without any problems, so its perfect (Completely rebuild CA18DET)