Page 2 of 3
Posted: Mon Apr 20, 2009 2:52 am
by TM_S13
do you mean "operations - select ECU consult registers" ? ?
if so, I can't access that... at least with the laptop not connected to the car...
Posted: Mon Apr 20, 2009 8:12 am
by kenbam
Matt, this keeps coming up, even with the latest address files you put up. I havent connected to car, just loading bin files i had on my laptop.
Posted: Mon Apr 20, 2009 2:03 pm
by iaredam
New version works great. The only thing is when I connect the LC-1, I get a msgbox saying couldn't connect to Innovate, but once I click Ok, it connects without a hitch... I can get a screen shot or a debug log if needed.
Posted: Tue Apr 21, 2009 11:00 am
by Matt
if you can get the exact error message for the Innovate I can hunt that one down... but I think I know what it is
Ken - Nistune scans the BIN file for a ECU part number 23710-XXXyy against an internal data base
If it finds that the part number is from a different ECU it will prompt you if you want to use the address file its detected. If you think its wrong you can click no
I've had to fine tune that since a B14 ROM contained a Z31 part number and misdetected (the XXX was contained at the end). I've made it now so that the 'yy' must be digits 0-9 so its a bit more strict in checking before reporting
Posted: Wed Apr 22, 2009 9:46 pm
by Matt
updated address files (some changes for B14 stuff)
Posted: Thu Apr 23, 2009 5:07 am
by iaredam
Matt wrote:if you can get the exact error message for the Innovate I can hunt that one down... but I think I know what it is
The exact error message is: "Innovate cannot find configured port COM0" - "Cannot connect to Innovate wideband"
Posted: Thu Apr 23, 2009 10:38 am
by Matt
okay thanks. i'll have a look at that
Posted: Tue Apr 28, 2009 1:28 am
by Matt
more updates to fix reversed duty time/cycle and ttp min/max display some ECUs
Posted: Thu Apr 30, 2009 2:18 am
by MichaS14a
Yesterday I made a few tests:
I burn the actual image again to the ECU (no changes made so far) and drive a little bit around (one time till 245 km/h
) but there is still no change at the AF Self Learn value. It stands fix at "100 %" the whole time.
What can I do? Should I do a reset of the learned values of the ECU or disconnect the battery (which has the same effect)?
Posted: Thu Apr 30, 2009 11:17 am
by Matt
I've noticed this in my R34 also... it stays at 100% all the time. Even in streamed mode.
I'll try again next time in datascan to see if that changes
Posted: Thu Apr 30, 2009 8:00 pm
by Fuzzy
Matt which board do you use in our R34?
Posted: Thu Apr 30, 2009 11:18 pm
by Matt
Type 4 board fits R34 (using adaptor C board to install it)
Only ER34 (GTT) however.... not HR34 (GT) or BNCR34 (GTR) since those use different ECUs which cant take a daugherboard
Posted: Sat May 02, 2009 9:58 pm
by Fuzzy
BCNR33 board in work?
Posted: Sat May 02, 2009 10:15 pm
by Matt
cant seem to reproduce the problems. please try a clean install and make sure your wideband folders are setup correctly
also can you post a log file from this for me to play back
I've included my log file for you to try and playback
My needles are also moving during playback
I believe this problem and the other one with invalid wideband values are related
Posted: Sat May 02, 2009 10:20 pm
by Matt
another test. on separate machine (test machine for this stuff)
please playback attached file... need to know if its realtime or playback issues from the log
here you can see everything updating. so im confused why your needles and values in tracer arent updating when mine are
