OEM Nissan sensor
Part number 22680-7S000. This is used on most current Nissan engines. Commonly referred to as the R35 GTR sensor but they’re actually used on everything from the GTR to the VK56 powered trucks and down to the lowly Tiida 4 cylinder. Nissan simply adjust the housing diameter to give them the required airflow range for the different engine sizes. Larger engines often use twin sensors. They’re good for around the same horsepower range as the Z32 MAF in a similar diameter housing but this can be adjusted by using different diameter housings. Beware of fake sensors. No horror stories yet, but there are Chinese fakes out there. Connectors are not currently available so the only option is to source used connectors from wrecks.
PMAS “HPX” sensor
These are a custom sensor developed by Precision Mass Airflow Sensors in USA. More expensive than the Nissan sensor but good for big horsepower. New connectors are available for these and they come with a generous length of wire attached. More details below.
Given that we like using the R35/HPX MAF inserts over Z32 MAFs these days and are strongly recommending workshops and customers do the same, below are links to where to get them and prices
PMAS HPX sensor
http://www.pmas-maf.com/hpx/#tab-1408391528718-3-4 $210USD
http://www.pmas-maf.com/product/pig-v $29USD
http://www.nistune.com/equipment-products.php
Sensor and pigtail currently $240AUD + GST (Aus) and freight. This may change depending on USD/AUD rates
R35 GTR sensor2.5″ housing 580 WHP
3″ housing 830 WHP
3.5″ housing 1130 WHP
The 22680-7S000 mass air flow sensor fits the following vehicles:From NZEFI: As a general rule, with this sensor a typical 3″ alloy tube (with internal diameter of 72.5mm) will support up to 350hp and 3.5″ alloy tube (with internal internal diameter of 85mm) will support up to 500hp. We’ve tested 4″ alloy tubes to over 600hp.
Kits (NZ EFI)2004-2008 Infiniti G35 3.5L V6 6 Cylinder
2008-2010 Infiniti G37 3.7L V6 6 Cylinder
2006-2010 Infiniti M35 3.5L V6 6 Cylinder
2006-2010 Infiniti M45 4.5L V8 8 Cylinder
2005-2006 Infiniti Q45 4.5L V8 8 Cylinder
2008-2010 Infiniti EX35 3.5L V6 6 Cylinder
2003-2010 Infiniti FX35 V6 6 Cylinder
2005-2008 Infiniti FX45 V8 8 Cylinder
2009-2010 Infiniti FX50 5.0L V8 8 Cylinder
2004-2010 Infiniti QX56 5.6L V8 8 Cylinder
2003-2009 Nissan 350Z 3.5L V6 6 Cylinder
2009-2010 Nissan 370Z 3.5L V6 6 Cylinder
2004-2010 Nissan Altima 2.5L I4 4 Cylinder
2004-2010 Nissan Altima 3.5L V6 6 Cylinder
2009-2010 Nissan Cube 1.8L I4 4 Cylinder
2009-2010 Nissan GT-R 3.8L V6 6 Cylinder Turbo
2004-2010 Nissan Maxima 3.5L V6 6 Cylinder
2007-2010 Nissan Sentra 2.0L I4 4 Cylinder
2004-2010 Nissan Sentra SE-R 2.5L I4 4 Cylinder
2007-2010 Nissan Tiida 1.8L I4 4 Cylinder
2009-2010 Nissan Versa 1.6L I4 4 Cylinder
2007-2010 Nissan Versa 1.8L I4 4 Cylinder
2005-2010 Nissan Armada 5.6L V8 8 Cylinder
2005-2010 Nissan Frontier 2.5L I4 4 Cylinder
2005-2010 Nissan Frontier 4.0L V6 6 Cylinder
2003-2010 Nissan Murano 3.5L V6 6 Cylinder
2004-2010 Nissan Pathfinder 4.0L V6 6 Cylinder
2008-2010 Nissan Pathfinder 5.6L V8 8 Cylinder
2004-2009 Nissan Quest 3.5L V6 6 Cylinder
2008-2010 Nissan Rogue 2.5L I4 4 Cylinder
2004-2010 Nissan Titan 5.6L V8 8 Cylinder
2004-2006 Nissan X-Trail 2.5L I4 4 Cylinder
2005-2010 Nissan Xterra 4.0L V6 6 Cylinder
2006-2008 Suzuki Grand Vitara 2.7L V6 6 Cylinder
http://www.nzefi.com/product/nissan-mas ... pgrade-kit
Plugs:
http://www.rhdjapan.com/hpi-r35-airflow ... rness.html
http://www.nzefi.com/product/nissan-350 ... connector/ $22NZD
Or just cut a plug from loom of one of the above listed Nissan vehicles (from wrecking yard)
Bungs
Allumunium bungs are welded to intercooler or intake piping depending on size. Using 3" and under only bung required. Use straightener for 3.5" - 4" tubing for airflow stability. Only install in a straight section of pipe (not on curves). Allow at least 1-2" straight tubing on each side of pipe. If installing in intake then ensure far enough from turbo (after bend) and use a recirculating BOV. Return from BOV should point away from MAF to avoid reversion.
More info here:
http://nistune.com/docs/Nistune%20MAF%2 ... 0Notes.pdf
Links for purchasing bungs below. I currently stock 3", 3.5" and 4" ones. I might get a few of the 2.5" and 2.75" for smaller pipes on my next order
2.5" bung
http://www.ebay.com/itm/2-5-OD-Slot-Sty ... 1816806014
2.75" bung
http://www.ebay.com/itm/2-75-OD-Slot-St ... 1866784396
3" bung
http://www.ebay.com/itm/3-0-OD-Slot-Sty ... 1816815136
3.5" bung
http://www.ebay.com/itm/3-5-OD-89mm-Mas ... 1845173271
4" bung
http://www.ebay.com/itm/4-0-OD-Mass-Air ... 1716765773
Links for purchasing straighteners below. I may stock a few of the 3.5" and 4" ones. However make sure they are fastened securely!!
Cost for these is $23.97USD plus freight
3.0” air straightener 5mm
http://www.ebay.com/itm/3-0-OD-76mm-OD- ... 1845173256
6mm
http://www.ebay.com/itm/3-0-OD-76mm-OD- ... 1913146245
3.5” Air straightener 5mm
http://www.ebay.com/itm/3-5-OD-89mm-OD- ... 1845173301
6mm
http://www.ebay.com/itm/3-5-OD-89mm-OD- ... 1845173266
4.0” Air straightener 5mm
http://www.ebay.com/itm/4-0-OD-102mm-OD ... 1903562952
6mm
http://www.ebay.com/itm/4-0-OD-102mm-OD ... 1913146252
Complete housing with bung and straightener about $93.97USD plus shipping
2.75” OD housing with straightener
http://www.ebay.com/itm/2-75-OD-MAF-Hou ... 1992453777
3.0” OD Housing with straightener
http://www.ebay.com/itm/3-0-OD-76mm-OD- ... 1743149029
http://www.ebay.com/itm/3-0-OD-x-8-MAF- ... 1734988955
3.25” OD Housing with straightener
http://www.ebay.com/itm/3-25-OD-MAF-Hou ... 1804232084
3.5” OD Housing with straightener
http://www.ebay.com/itm/3-50-OD-x-8-MAF ... 2035841270
4.0” OD Housing with straightener
http://www.ebay.com/itm/4-0-OD-MAF-Hous ... 2080319202