Nistune Forums

Thank you.

Where I can find safeboost limit in Nistune?
I only found in DTC filter 2 - Boost Pressure Sensor.

Hi, I have a simple question, have Z32 TT from 1993 electronically controlled boost by ECU? Which table is it in Nistune?
Or for little increase of boost is need to have boost controller.

Thanks for answer.

Hi Matt, thank you for helping me. So dyno AFRs reading is really hard to do for me. Which AFRs logs can help to you? I am now using Ford Lightning MAF, previously I was using Cobra MAF and AFR curves from nistune for them. So It is bad using them? I dont know where I can found correct VQ maps for t...

Hi, I really thanks for help me with my problem. 1987 Z31 VG30ET , Twin Garretts GT2860RS, JWT stage2 cams, 750ccm Siemens Injectors, Ford Lightning MAF, Greddy E-01 Boost Controller, Walbro 255lph fuel pump, Aeromotive Fuel Preassure regulator, NGK BCPR6E, Magnecore R100 ignition cables When is eng...

steve_s13 wrote:Ill be milling out a P11 for a lad here in the UK Matt, so Ill try and do a step by step if anyone is interested

Of course it will be interesting.

I want upgrade frame too.

Hi, is there any nistune board available for P11 Primera with SR20DE engine?

I found only post from year 2007, where is supported only P10 Primera ECU.

Thanks for information.

I am finishing ECU tune, almost everything is working well, ride with car is amazing, only clutch as I am saying in other post, it cannot handle increasment of torque. Idle is running AFR 14,5-14,8 , I think because of JWT C2 cams are installed it is good. Idle is little unstable 680-780 rpms, but I...

Friend of my, he find for me 54481 Assy Bracket so I need only now

54480(RH) Assy Bracket-Tension rod for +8/1987 Z31 new shape, if someone can help me find this parts, I will be very happy. New or Old(good condition)...

Thx

Well if it's Z32 we in Nistune "family" have http://dta-motorsport.com/ but for Z31 try this http://www.rhdjapan.com/jdm-low/NEW-OS-Giken-TS2BD-Twin-Plate-Clutch-Kit-NISSAN-480HP-11856 We buy lot stuff from them so You can contact them with OEM part number and they will put that part on s...

Hi, so right now i have little problem with my setup. My engine is producing so much torque that clutch cannot handle. I have Clutchmaster Stage V clutch kit with Fidanza Alu Flywheel. When engine reach 4500 rmps clutch is slippering.... (Clutch and flywheel were new and I drove around 700km without...

good to hear you got it working. its been a while, firstly when you were using the Vein Pressure converter a while ago just make sure your boost AFRs are right with that fuel map and checking for knock and should be all good. I cant see them in the log you will need to check on your end Yes, VPC wa...

Point something is wrong was good :) You said it looks like VQ read and K constant problem. When was VQ from Z32 and Cobra MAF engine was running much better then Cobra VQ map and Cobra MAF together. So I was thinking about what if and I started comparing VQ maps, so i found that Lightning VQ map is...

hi, so as you said there was Z32 VQ map, so i used your BIN file and engine is now working in different way. If I read nistune manual right, I start with finding K constant for new setup. So O2 sensor disconnected, engine warmed up ( if it is possible ), Fuel Injection map in Filtered value set to 0...

Thank you. :) So I made some more test when I was downloading BIN file. Dont be scary when you will see BIN is little mess. So my problem is happening only when engine is warmed up. Until aprox 70-75 degrees of celsius there isnt problem floor it. Problem is only when engine reach operating temperat...

I was experimenting with this on Z31 VG30ET but without good result.

I was using HKS VPC with Z32TT Eprom but signal wasnt perfect.

If you want use MAP correctly and if you want maximum result use some ECU which support MAP sensor at all. Haltech or better.